The arrows are not updated realtime. Only after a toggle off/on of the status of the indicator the arrows are updated. The Update on every Tick is in the active status.
See the arrows in the pictures
Eur n01 is before the status off/on.
Eur n02 is after the toggle off/on.
Indicator not updating
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
- Attachments
-
- Eur n01.png
- (40.43 KiB) Downloaded 1295 times
-
- Eur n02.png
- (40.8 KiB) Downloaded 1300 times
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
Oeps this belongs to the new beta. and should be placed there
- Stanley Miller
- Posts: 556
- Joined: Jul 26 2005
- Has thanked: 3 times
Pipscalper, we can't reproduce the problem for some reasons. What I'm doing is apply the following indicator and it adds the new arrow on every new bar without any problems. Could you please confirm this?
Code: Select all
var: id(0);
id = arw_new(d,t,h,true);
arw_setstyle(id, 10);
arw_setsize(id, 3);
arw_setcolor(id,red);
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
I think we found a [possible reason Stanley.
This indicator applied to a normal chart with 1 data plot works fine .
However I used the indicator on a 3 data chart .
data1 being 5 min
data2 being 1 min
data3 being 15 min
The indicator applied on this 3data chart based on data 2 does not update.
So seems the problem lies in the multidata chart.
Regards
This indicator applied to a normal chart with 1 data plot works fine .
However I used the indicator on a 3 data chart .
data1 being 5 min
data2 being 1 min
data3 being 15 min
The indicator applied on this 3data chart based on data 2 does not update.
So seems the problem lies in the multidata chart.
Regards
- Stanley Miller
- Posts: 556
- Joined: Jul 26 2005
- Has thanked: 3 times
Could you please send us the indicator?
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
I did sent it already to Kate, but also your little code with the red arrows does not update in the multi data chart. But it does work in a single data chart.
regards
regards
- Stanley Miller
- Posts: 556
- Joined: Jul 26 2005
- Has thanked: 3 times
I can't see it so far. Could you please describe me step by step how to reproduce it?also your little code with the red arrows does not update in the multi data chart. But it does work in a single data chart.
regards
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
after opening a new chart the indicator works well in the new chart and is updated correctly . Not so however in the old charts. Could something have gone wrong during the install of the beta.
I only have to renew all charts from the beginning and then everything will work again as normal.
Sorry for the inconvenience caused.
regards
I only have to renew all charts from the beginning and then everything will work again as normal.
Sorry for the inconvenience caused.
regards
- Stanley Miller
- Posts: 556
- Joined: Jul 26 2005
- Has thanked: 3 times
So what should I do to reproduce the issue? Create a chart, apply the indicator, save a workspace, then reopen it? Is this what you are doing?
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
I dont know what the cause is.
For your info I can give following details.
I have open 10-12 workspaces.
Each workspace has about 3 chartwindows ,with a load of 4-5 symbols
The data range loaded is aprox 1000 bars each.
As I feel MC is a little bit pushed to the limit here due to the big dataloads, and my computer is not so young anymore.
Before the beta update it worked well , after the update only update after toggle on/off in the formatwindow.
If I install a fresh new chart it works again OK.
So it seems not to be a program bug .
Hope this info is of use to you
regards
For your info I can give following details.
I have open 10-12 workspaces.
Each workspace has about 3 chartwindows ,with a load of 4-5 symbols
The data range loaded is aprox 1000 bars each.
As I feel MC is a little bit pushed to the limit here due to the big dataloads, and my computer is not so young anymore.
Before the beta update it worked well , after the update only update after toggle on/off in the formatwindow.
If I install a fresh new chart it works again OK.
So it seems not to be a program bug .
Hope this info is of use to you
regards
@Stanley
I have the same problem that indicator generated text and drawing outputs sometimes dissapear and i have to turn status off/on to bring it back.
You can reproduce it using the ARPS FREE UNVIVERSAL SWING TOOL under Add-on. If i use "Update every tick" it sometime stopp working on tick/volume charts..
I have the same problem that indicator generated text and drawing outputs sometimes dissapear and i have to turn status off/on to bring it back.
You can reproduce it using the ARPS FREE UNVIVERSAL SWING TOOL under Add-on. If i use "Update every tick" it sometime stopp working on tick/volume charts..
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
Stanley the problem is again back.
Attached i sent you a linReg channel indicator and an adaptive+ mov. average.
If I apply the LinReg channel to a 1 hr chart, it works OK, if I add the adaptive movAv+Fib ,then the LinReg channel disappears.
Hope this can give you an indication of the problem
Attached i sent you a linReg channel indicator and an adaptive+ mov. average.
If I apply the LinReg channel to a 1 hr chart, it works OK, if I add the adaptive movAv+Fib ,then the LinReg channel disappears.
Hope this can give you an indication of the problem
- Attachments
-
- LR+Kma.xml
- (51.54 KiB) Downloaded 557 times
- Stanley Miller
- Posts: 556
- Joined: Jul 26 2005
- Has thanked: 3 times
Thank you very much for the reports. We have been able to reproduce the problem and it should be fixed in the new beta.
-
- Posts: 84
- Joined: Jul 28 2006
- Been thanked: 3 times
Glad that I could be of any help to you Stanley.